Всё больше в моду входят твёрдотельные накопители информации, по-простому — SSD диски (англ. Solid-State Drive). Технический прогресс делает их всё более доступными для рядового пользователя, а производители всё увереннее заявляют об их надёжности. Преимущества SSD очевидны. Первое, что замечаешь после замены обычно жёсткого диска (НЖМД, англ. HDD) на SSD — скорость загрузки операционной системы и скорость запуска программ. Я в восторге от работы SSD.
Нет ничего вечного. Мой SSD не проработал и полгода. На днях просто завис компьютер. Намертво завис — в прямом смысле этого слова. После попытки его перезагрузить выскочила ошибка загрузки — типа, операционная система не найдена. Вот так я впервые увидел, как погибает SSD. Он просто перестал работать. Без никаких предвестников. Я несколько раз видел, как гибнут обычные HDD. Обычно предвестниками скорой гибели являются ошибки чтения/записи, устройство начинает издавать необычные звуки и т.д. Здесь же всё произошло без предварительных симптомов — в один момент. Опишу, как выглядит эта гибель в операционной системе Linux.
Первым делом подключил SSD через USB/SATA конвертер к работающему компьютеру.
Вот что увидел в dmesg в течение 30 секунд (спойлер):
[ 1809.180135] usb 1-2: new high-speed USB device number 5 using xhci_hcd
[ 1809.321599] usb 1-2: New USB device found, idVendor=14cd, idProduct=6116, bcdDevice= 2.20
[ 1809.321619] usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[ 1809.321629] usb 1-2: Product: USB Mass Storage Device
[ 1809.321635] usb 1-2: Manufacturer: Generic
[ 1809.321642] usb 1-2: SerialNumber: 116AC2101219
[ 1809.323262] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 1809.323810] scsi host3: usb-storage 1-2:1.0
[ 1810.334794] scsi 3:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0
[ 1810.341364] sd 3:0:0:0: [sdb] 500118190 512-byte logical blocks: (256 GB/238 GiB)
[ 1810.341591] sd 3:0:0:0: [sdb] Write Protect is off
[ 1810.341600] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1810.341796] sd 3:0:0:0: [sdb] No Caching mode page found
[ 1810.341808] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1824.039987] usb 1-2: USB disconnect, device number 5
[ 1824.053299] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053337] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1824.053360] blk_update_request: I/O error, dev sdb, sector 2 op 0x0:(READ) flags 0x0 phys_seg 3 prio class 0
[ 1824.053374] Buffer I/O error on dev sdb, logical block 1, async page read
[ 1824.053382] Buffer I/O error on dev sdb, logical block 2, async page read
[ 1824.053389] Buffer I/O error on dev sdb, logical block 3, async page read
[ 1824.053589] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053616] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1824.053652] blk_update_request: I/O error, dev sdb, sector 2 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053665] Buffer I/O error on dev sdb, logical block 1, async page read
[ 1824.053688] blk_update_request: I/O error, dev sdb, sector 4 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053699] Buffer I/O error on dev sdb, logical block 2, async page read
[ 1824.053719] blk_update_request: I/O error, dev sdb, sector 6 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053729] Buffer I/O error on dev sdb, logical block 3, async page read
[ 1824.053742] ldm_validate_partition_table(): Disk read failed.
[ 1824.053768] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053778] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1824.053798] blk_update_request: I/O error, dev sdb, sector 2 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053807] Buffer I/O error on dev sdb, logical block 1, async page read
[ 1824.053827] blk_update_request: I/O error, dev sdb, sector 4 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053849] blk_update_request: I/O error, dev sdb, sector 6 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1824.053993] sdb: unable to read partition table
[ 1824.080499] sd 3:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 1824.080515] sd 3:0:0:0: [sdb] Sense not available.
[ 1824.080529] sd 3:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 1824.080550] sdb: detected capacity change from 500118190 to 0
[ 1824.080561] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 1836.126808] usb 1-2: new high-speed USB device number 6 using xhci_hcd
[ 1836.268288] usb 1-2: New USB device found, idVendor=14cd, idProduct=6116, bcdDevice= 2.20
[ 1836.268308] usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[ 1836.268318] usb 1-2: Product: USB Mass Storage Device
[ 1836.268325] usb 1-2: Manufacturer: Generic
[ 1836.268331] usb 1-2: SerialNumber: 116AC2101219
[ 1836.274295] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 1836.275010] scsi host3: usb-storage 1-2:1.0
[ 1837.293897] scsi 3:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0
[ 1837.300536] sd 3:0:0:0: [sdb] 500118190 512-byte logical blocks: (256 GB/238 GiB)
[ 1837.300798] sd 3:0:0:0: [sdb] Write Protect is off
[ 1837.300810] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1837.301035] sd 3:0:0:0: [sdb] No Caching mode page found
[ 1837.301055] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1837.342928] sd 3:0:0:0: [sdb] Attached SCSI diskВывод команды smartctl -a /dev/sdb -s on (спойлер):
smartctl -a /dev/sdb -s on
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.7-arch1-1] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SATAFIRM S11
Serial Number: SN204108935913
Firmware Version: SBFMP1W3
User Capacity: 256 060 514 304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sun Aug 8 12:49:20 2021 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (65535) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 815935
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 48169692
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0
170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 77
173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 281474976710655
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 0
194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 0/33)
218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
231 Unknown_SSD_Attribute 0x0013 100 100 000 Pre-fail Always - 0
241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 102678122519
SMART Error Log Version: 1
No Errors Logged
Read SMART Self-test Log failed: SAT command failed
Read SMART Selective Self-test Log failed: SAT command failedВ выводе утилиты smartctl удивило значение Power_on_Hours 815935 — это почти 34000 суток или более 90 лет. Возможно, там не часы, а какие-то свои единицы измерения. Но и Power_Cycle_Count — количество циклов включения/выключения цифра 48169692 нереальная.
Использую утилиту cfdisk. cfdisk /dev/sdb — предлагает выбрать тип используемой таблицы разделов. У меня был dos:
Можно было бы попробовать его сейчас разметить, но в душе ещё теплится надежда восстановить информацию, по-этому, для начала, попробую использую TestDisk. TestDisk начинает сканировать. На 3-ем секторе пауза, затем сканирование продолжается. Программа завершает свою работу:
Смотрю dmesg — за время работы TestDisk высыпались ошибки (спойлер):
[ 2237.145182] usb 1-2: USB disconnect, device number 6
[ 2237.145418] sd 3:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=13s
[ 2237.145439] sd 3:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 d0 10 00 00 20 00
[ 2237.145449] print_req_error: 8 callbacks suppressed
[ 2237.145455] blk_update_request: I/O error, dev sdb, sector 53264 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 2237.145627] blk_update_request: I/O error, dev sdb, sector 53264 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.145663] buffer_io_error: 10 callbacks suppressed
[ 2237.145671] Buffer I/O error on dev sdb, logical block 26632, async page read
[ 2237.145695] blk_update_request: I/O error, dev sdb, sector 53266 op 0x0:(READ) flags 0x0 phys_seg 3 prio class 0
[ 2237.145715] Buffer I/O error on dev sdb, logical block 26633, async page read
[ 2237.145725] Buffer I/O error on dev sdb, logical block 26634, async page read
[ 2237.145733] Buffer I/O error on dev sdb, logical block 26635, async page read
[ 2237.146078] blk_update_request: I/O error, dev sdb, sector 53264 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.146105] Buffer I/O error on dev sdb, logical block 26632, async page read
[ 2237.146693] blk_update_request: I/O error, dev sdb, sector 53266 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.146721] Buffer I/O error on dev sdb, logical block 26633, async page read
[ 2237.146761] blk_update_request: I/O error, dev sdb, sector 53268 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.146774] Buffer I/O error on dev sdb, logical block 26634, async page read
[ 2237.146809] blk_update_request: I/O error, dev sdb, sector 53270 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.146828] Buffer I/O error on dev sdb, logical block 26635, async page read
[ 2237.146943] blk_update_request: I/O error, dev sdb, sector 53304 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 2237.147011] blk_update_request: I/O error, dev sdb, sector 53304 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.147027] Buffer I/O error on dev sdb, logical block 26652, async page read
[ 2237.147067] blk_update_request: I/O error, dev sdb, sector 53306 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 2237.147082] Buffer I/O error on dev sdb, logical block 26653, async page read
[ 2250.106055] usb 1-2: new high-speed USB device number 7 using xhci_hcd
[ 2250.247532] usb 1-2: New USB device found, idVendor=14cd, idProduct=6116, bcdDevice= 2.20
[ 2250.247551] usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[ 2250.247560] usb 1-2: Product: USB Mass Storage Device
[ 2250.247567] usb 1-2: Manufacturer: Generic
[ 2250.247573] usb 1-2: SerialNumber: 116AC2101219
[ 2250.249178] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 2250.249733] scsi host4: usb-storage 1-2:1.0
[ 2251.259723] scsi 4:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0
[ 2251.266332] sd 4:0:0:0: [sdc] 500118190 512-byte logical blocks: (256 GB/238 GiB)
[ 2251.266661] sd 4:0:0:0: [sdc] Write Protect is off
[ 2251.266672] sd 4:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 2251.266857] sd 4:0:0:0: [sdc] No Caching mode page found
[ 2251.266871] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2251.328178] sd 4:0:0:0: [sdc] Attached SCSI diskВ окне TestDisk Жму Enter и выбираю deeper search.
так же безрезультатно.
Анализируя ошибки dmesg, делаю вывод, что SSD отключается при попытке обращения к нему, о чём свидетельствуют строчки:
[ 1824.039987] usb 1-2: USB disconnect, device number 5
[ 2237.145182] usb 1-2: USB disconnect, device number 6все последующие ошибки — ошибки обращения к несуществующему устройству.
Надо попробовать подключить устройство к SATA, без посредников.
Снова ошибки в dmesg (спойлер):
[ 72.603236] ata5: link is slow to respond, please be patient (ready=0)
[ 77.273241] ata5: COMRESET failed (errno=-16)
[ 82.643238] ata5: link is slow to respond, please be patient (ready=0)
[ 87.283236] ata5: COMRESET failed (errno=-16)
[ 92.673234] ata5: link is slow to respond, please be patient (ready=0)
[ 122.353232] ata5: COMRESET failed (errno=-16)
[ 122.353240] ata5: limiting SATA link speed to 1.5 Gbps
[ 127.393232] ata5: COMRESET failed (errno=-16)
[ 127.393239] ata5: reset failed, giving up
[ 127.393242] ata5.00: disabled
[ 127.393292] sd 4:0:0:0: [sdc] tag#18 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=82s
[ 127.393297] sd 4:0:0:0: [sdc] tag#18 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 127.393302] blk_update_request: I/O error, dev sdc, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 127.393400] sd 4:0:0:0: [sdc] Read Capacity(16) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 127.393402] sd 4:0:0:0: [sdc] Sense not available.
[ 127.393426] sd 4:0:0:0: [sdc] Read Capacity(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 127.393427] sd 4:0:0:0: [sdc] Sense not available.
[ 127.393454] sd 4:0:0:0: [sdc] 0 512-byte logical blocks: (0 B/0 B)
[ 127.393675] sdc: detected capacity change from 256060514304 to 0
[ 139.594009] sd 4:0:0:0: [sdc] Read Capacity(16) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 139.594013] sd 4:0:0:0: [sdc] Sense not available.
[ 139.594050] sd 4:0:0:0: [sdc] Read Capacity(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 139.594053] sd 4:0:0:0: [sdc] Sense not available.[ 282.003232] ata5: SATA link down (SStatus 0 SControl 300)Мда, всё как-то лучше не становится. Отключаю/подключаю разъём SATA
Сообщения dmesg (спойлер):
[ 282.003251] ata5.00: detaching (SCSI 4:0:0:0)
[ 282.006959] sd 4:0:0:0: [sdc] Stopping disk
[ 282.006989] sd 4:0:0:0: [sdc] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 289.233228] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 289.233339] ata5.00: ATA-11: SATAFIRM S11, SBFMP1W3, max UDMA/133
[ 289.233341] ata5.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 289.233439] ata5.00: configured for UDMA/133
[ 289.233549] scsi 4:0:0:0: Direct-Access ATA SATAFIRM S11 P1W3 PQ: 0 ANSI: 5
[ 289.233973] sd 4:0:0:0: [sdc] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 289.233986] sd 4:0:0:0: [sdc] Write Protect is off
[ 289.233988] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 289.234008] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 289.333439] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 290.733229] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 290.733440] ata5.00: configured for UDMA/133Запускаю TestDisk.
Снова долгая пауза на 3-ем секторе. В dmesg сыпятся ошибки (спойлер):
[ 342.603228] ata5.00: exception Emask 0x10 SAct 0x20000000 SErr 0x4050002 action 0xe frozen
[ 342.603231] ata5.00: irq_stat 0x00400040, connection status changed
[ 342.603234] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 342.603237] ata5.00: failed command: READ FPDMA QUEUED
[ 342.603243] ata5.00: cmd 60/18:e8:38:d0:00/00:00:00:00:00/40 tag 29 ncq dma 12288 in
res 40/00:e0:10:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 342.603244] ata5.00: status: { DRDY }
[ 342.603248] ata5: hard resetting link
[ 343.353221] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 343.353420] ata5.00: configured for UDMA/133
[ 343.353433] sd 4:0:0:0: [sdc] tag#29 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 343.353437] sd 4:0:0:0: [sdc] tag#29 Sense Key : Illegal Request [current]
[ 343.353440] sd 4:0:0:0: [sdc] tag#29 Add. Sense: Unaligned write command
[ 343.353444] sd 4:0:0:0: [sdc] tag#29 CDB: Read(10) 28 00 00 00 d0 38 00 00 18 00
[ 343.353448] blk_update_request: I/O error, dev sdc, sector 53304 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 343.353459] ata5: EH complete
[ 344.033221] ata5.00: exception Emask 0x10 SAct 0x2000 SErr 0x4050002 action 0xe frozen
[ 344.033224] ata5.00: irq_stat 0x00400040, connection status changed
[ 344.033227] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 344.033229] ata5.00: failed command: READ FPDMA QUEUED
[ 344.033235] ata5.00: cmd 60/08:68:40:d0:00/00:00:00:00:00/40 tag 13 ncq dma 4096 in
res 40/00:48:38:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 344.033236] ata5.00: status: { DRDY }
[ 344.033239] ata5: hard resetting link
[ 344.803221] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 344.803424] ata5.00: configured for UDMA/133
[ 344.803431] ata5: EH complete
[ 345.493228] ata5: limiting SATA link speed to 1.5 Gbps
[ 345.493233] ata5.00: exception Emask 0x10 SAct 0x1000 SErr 0x4050002 action 0xe frozen
[ 345.493234] ata5.00: irq_stat 0x00400040, connection status changed
[ 345.493237] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 345.493240] ata5.00: failed command: READ FPDMA QUEUED
[ 345.493246] ata5.00: cmd 60/08:60:48:d0:00/00:00:00:00:00/40 tag 12 ncq dma 4096 in
res 40/00:30:40:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 345.493247] ata5.00: status: { DRDY }
[ 345.493251] ata5: hard resetting link
[ 346.223232] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 346.223449] ata5.00: configured for UDMA/133
[ 346.223461] ata5: EH complete
[ 346.903226] ata5.00: exception Emask 0x10 SAct 0x100 SErr 0x4050002 action 0xe frozen
[ 346.903230] ata5.00: irq_stat 0x00400040, connection status changed
[ 346.903233] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 346.903236] ata5.00: failed command: READ FPDMA QUEUED
[ 346.903241] ata5.00: cmd 60/20:40:50:d0:00/00:00:00:00:00/40 tag 8 ncq dma 16384 in
res 40/00:30:48:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 346.903243] ata5.00: status: { DRDY }
[ 346.903247] ata5: hard resetting link
[ 347.633221] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 347.633439] ata5.00: configured for UDMA/133
[ 347.633454] sd 4:0:0:0: [sdc] tag#8 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 347.633458] sd 4:0:0:0: [sdc] tag#8 Sense Key : Illegal Request [current]
[ 347.633461] sd 4:0:0:0: [sdc] tag#8 Add. Sense: Unaligned write command
[ 347.633465] sd 4:0:0:0: [sdc] tag#8 CDB: Read(10) 28 00 00 00 d0 50 00 00 20 00
[ 347.633468] blk_update_request: I/O error, dev sdc, sector 53328 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 347.633485] ata5: EH complete
[ 348.313232] ata5.00: exception Emask 0x10 SAct 0x200000 SErr 0x4050002 action 0xe frozen
[ 348.313235] ata5.00: irq_stat 0x00400040, connection status changed
[ 348.313238] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 348.313241] ata5.00: failed command: READ FPDMA QUEUED
[ 348.313247] ata5.00: cmd 60/08:a8:58:d0:00/00:00:00:00:00/40 tag 21 ncq dma 4096 in
res 40/00:98:50:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 348.313248] ata5.00: status: { DRDY }
[ 348.313252] ata5: hard resetting link
[ 349.043231] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 349.043453] ata5.00: configured for UDMA/133
[ 349.043468] ata5: EH complete
[ 349.733216] ata5.00: exception Emask 0x10 SAct 0x8000000 SErr 0x4050002 action 0xe frozen
[ 349.733220] ata5.00: irq_stat 0x00400040, connection status changed
[ 349.733222] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 349.733225] ata5.00: failed command: READ FPDMA QUEUED
[ 349.733231] ata5.00: cmd 60/18:d8:78:d0:00/00:00:00:00:00/40 tag 27 ncq dma 12288 in
res 40/00:58:58:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 349.733233] ata5.00: status: { DRDY }
[ 349.733235] ata5: hard resetting link
[ 350.463223] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 350.463434] ata5.00: configured for UDMA/133
[ 350.463449] sd 4:0:0:0: [sdc] tag#27 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 350.463452] sd 4:0:0:0: [sdc] tag#27 Sense Key : Illegal Request [current]
[ 350.463456] sd 4:0:0:0: [sdc] tag#27 Add. Sense: Unaligned write command
[ 350.463459] sd 4:0:0:0: [sdc] tag#27 CDB: Read(10) 28 00 00 00 d0 78 00 00 18 00
[ 350.463463] blk_update_request: I/O error, dev sdc, sector 53368 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 350.463478] ata5: EH complete
[ 351.143226] ata5.00: limiting speed to UDMA/100:PIO4
[ 351.143231] ata5.00: exception Emask 0x10 SAct 0x100000 SErr 0x4050002 action 0xe frozen
[ 351.143233] ata5.00: irq_stat 0x00400040, connection status changed
[ 351.143236] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 351.143239] ata5.00: failed command: READ FPDMA QUEUED
[ 351.143244] ata5.00: cmd 60/08:a0:80:d0:00/00:00:00:00:00/40 tag 20 ncq dma 4096 in
res 40/00:78:78:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 351.143246] ata5.00: status: { DRDY }
[ 351.143250] ata5: hard resetting link
[ 351.893225] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 351.893451] ata5.00: configured for UDMA/100
[ 351.893463] ata5: EH complete
[ 352.583220] ata5.00: exception Emask 0x10 SAct 0x1000000 SErr 0x4050002 action 0xe frozen
[ 352.583223] ata5.00: irq_stat 0x00400040, connection status changed
[ 352.583226] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 352.583228] ata5.00: failed command: READ FPDMA QUEUED
[ 352.583234] ata5.00: cmd 60/08:c0:88:d0:00/00:00:00:00:00/40 tag 24 ncq dma 4096 in
res 40/00:90:80:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 352.583236] ata5.00: status: { DRDY }
[ 352.583238] ata5: hard resetting link
[ 353.343221] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 353.343436] ata5.00: configured for UDMA/100
[ 353.343444] ata5: EH complete
[ 354.023234] ata5.00: exception Emask 0x10 SAct 0x80000 SErr 0x4050002 action 0xe frozen
[ 354.023239] ata5.00: irq_stat 0x00400040, connection status changed
[ 354.023242] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 354.023245] ata5.00: failed command: READ FPDMA QUEUED
[ 354.023251] ata5.00: cmd 60/10:98:00:d8:00/00:00:00:00:00/40 tag 19 ncq dma 8192 in
res 40/00:60:88:d0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 354.023253] ata5.00: status: { DRDY }
[ 354.023257] ata5: hard resetting link
[ 354.763225] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 354.763455] ata5.00: configured for UDMA/100
[ 354.763472] sd 4:0:0:0: [sdc] tag#19 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 354.763476] sd 4:0:0:0: [sdc] tag#19 Sense Key : Illegal Request [current]
[ 354.763479] sd 4:0:0:0: [sdc] tag#19 Add. Sense: Unaligned write command
[ 354.763483] sd 4:0:0:0: [sdc] tag#19 CDB: Read(10) 28 00 00 00 d8 00 00 00 10 00
[ 354.763487] blk_update_request: I/O error, dev sdc, sector 55296 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 354.763506] ata5: EH complete
[ 355.443231] ata5.00: exception Emask 0x10 SAct 0x20000 SErr 0x4050002 action 0xe frozen
[ 355.443234] ata5.00: irq_stat 0x00400040, connection status changed
[ 355.443237] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 355.443239] ata5.00: failed command: READ FPDMA QUEUED
[ 355.443245] ata5.00: cmd 60/20:88:10:e0:00/00:00:00:00:00/40 tag 17 ncq dma 16384 in
res 40/00:80:00:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 355.443247] ata5.00: status: { DRDY }
[ 355.443250] ata5: hard resetting link
[ 356.183223] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 356.183447] ata5.00: configured for UDMA/100
[ 356.183462] sd 4:0:0:0: [sdc] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 356.183466] sd 4:0:0:0: [sdc] tag#17 Sense Key : Illegal Request [current]
[ 356.183469] sd 4:0:0:0: [sdc] tag#17 Add. Sense: Unaligned write command
[ 356.183472] sd 4:0:0:0: [sdc] tag#17 CDB: Read(10) 28 00 00 00 e0 10 00 00 20 00
[ 356.183476] blk_update_request: I/O error, dev sdc, sector 57360 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 356.183491] ata5: EH complete
[ 356.863238] ata5.00: limiting speed to UDMA/33:PIO4
[ 356.863242] ata5.00: exception Emask 0x10 SAct 0x40000 SErr 0x4050002 action 0xe frozen
[ 356.863244] ata5.00: irq_stat 0x00400040, connection status changed
[ 356.863246] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 356.863249] ata5.00: failed command: READ FPDMA QUEUED
[ 356.863255] ata5.00: cmd 60/08:90:18:e0:00/00:00:00:00:00/40 tag 18 ncq dma 4096 in
res 40/00:10:10:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 356.863256] ata5.00: status: { DRDY }
[ 356.863259] ata5: hard resetting link
[ 357.603225] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 357.603456] ata5.00: configured for UDMA/33
[ 357.603469] ata5: EH complete
[ 358.293216] ata5.00: exception Emask 0x10 SAct 0x40 SErr 0x4050002 action 0xe frozen
[ 358.293218] ata5.00: irq_stat 0x00400040, connection status changed
[ 358.293221] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 358.293223] ata5.00: failed command: READ FPDMA QUEUED
[ 358.293229] ata5.00: cmd 60/18:30:38:e0:00/00:00:00:00:00/40 tag 6 ncq dma 12288 in
res 40/00:00:18:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 358.293231] ata5.00: status: { DRDY }
[ 358.293234] ata5: hard resetting link
[ 359.063228] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 359.063443] ata5.00: configured for UDMA/33
[ 359.063457] sd 4:0:0:0: [sdc] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 359.063461] sd 4:0:0:0: [sdc] tag#6 Sense Key : Illegal Request [current]
[ 359.063464] sd 4:0:0:0: [sdc] tag#6 Add. Sense: Unaligned write command
[ 359.063468] sd 4:0:0:0: [sdc] tag#6 CDB: Read(10) 28 00 00 00 e0 38 00 00 18 00
[ 359.063471] blk_update_request: I/O error, dev sdc, sector 57400 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 359.063484] ata5: EH complete
[ 359.743214] ata5.00: exception Emask 0x10 SAct 0x10000000 SErr 0x4050002 action 0xe frozen
[ 359.743217] ata5.00: irq_stat 0x00400040, connection status changed
[ 359.743220] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 359.743223] ata5.00: failed command: READ FPDMA QUEUED
[ 359.743228] ata5.00: cmd 60/08:e0:40:e0:00/00:00:00:00:00/40 tag 28 ncq dma 4096 in
res 40/00:b8:38:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 359.743230] ata5.00: status: { DRDY }
[ 359.743232] ata5: hard resetting link
[ 360.523223] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 360.523446] ata5.00: configured for UDMA/33
[ 360.523458] ata5: EH complete
[ 361.213221] ata5.00: exception Emask 0x10 SAct 0x20 SErr 0x4050002 action 0xe frozen
[ 361.213224] ata5.00: irq_stat 0x00400040, connection status changed
[ 361.213226] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 361.213229] ata5.00: failed command: READ FPDMA QUEUED
[ 361.213235] ata5.00: cmd 60/08:28:48:e0:00/00:00:00:00:00/40 tag 5 ncq dma 4096 in
res 40/00:08:40:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 361.213236] ata5.00: status: { DRDY }
[ 361.213240] ata5: hard resetting link
[ 361.953234] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 361.953449] ata5.00: configured for UDMA/33
[ 361.953460] ata5: EH complete
[ 362.633220] ata5.00: exception Emask 0x10 SAct 0x4 SErr 0x4050002 action 0xe frozen
[ 362.633222] ata5.00: irq_stat 0x00400040, connection status changed
[ 362.633224] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 362.633227] ata5.00: failed command: READ FPDMA QUEUED
[ 362.633233] ata5.00: cmd 60/20:10:50:e0:00/00:00:00:00:00/40 tag 2 ncq dma 16384 in
res 40/00:e0:48:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 362.633235] ata5.00: status: { DRDY }
[ 362.633238] ata5: hard resetting link
[ 363.363228] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 363.363454] ata5.00: configured for UDMA/33
[ 363.363473] sd 4:0:0:0: [sdc] tag#2 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 363.363477] sd 4:0:0:0: [sdc] tag#2 Sense Key : Illegal Request [current]
[ 363.363480] sd 4:0:0:0: [sdc] tag#2 Add. Sense: Unaligned write command
[ 363.363484] sd 4:0:0:0: [sdc] tag#2 CDB: Read(10) 28 00 00 00 e0 50 00 00 20 00
[ 363.363487] blk_update_request: I/O error, dev sdc, sector 57424 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 363.363508] ata5: EH complete
[ 364.053222] ata5.00: exception Emask 0x10 SAct 0x1000 SErr 0x4050002 action 0xe frozen
[ 364.053224] ata5.00: irq_stat 0x00400040, connection status changed
[ 364.053227] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 364.053230] ata5.00: failed command: READ FPDMA QUEUED
[ 364.053235] ata5.00: cmd 60/08:60:58:e0:00/00:00:00:00:00/40 tag 12 ncq dma 4096 in
res 40/00:a0:50:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 364.053237] ata5.00: status: { DRDY }
[ 364.053240] ata5: hard resetting link
[ 364.823219] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 364.823426] ata5.00: configured for UDMA/33
[ 364.823434] ata5: EH complete
[ 365.513224] ata5.00: exception Emask 0x10 SAct 0x2000000 SErr 0x4050002 action 0xe frozen
[ 365.513227] ata5.00: irq_stat 0x00400040, connection status changed
[ 365.513230] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 365.513233] ata5.00: failed command: READ FPDMA QUEUED
[ 365.513238] ata5.00: cmd 60/18:c8:78:e0:00/00:00:00:00:00/40 tag 25 ncq dma 12288 in
res 40/00:78:58:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 365.513240] ata5.00: status: { DRDY }
[ 365.513244] ata5: hard resetting link
[ 366.293228] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 366.293451] ata5.00: configured for UDMA/33
[ 366.293471] sd 4:0:0:0: [sdc] tag#25 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 366.293475] sd 4:0:0:0: [sdc] tag#25 Sense Key : Illegal Request [current]
[ 366.293478] sd 4:0:0:0: [sdc] tag#25 Add. Sense: Unaligned write command
[ 366.293481] sd 4:0:0:0: [sdc] tag#25 CDB: Read(10) 28 00 00 00 e0 78 00 00 18 00
[ 366.293485] blk_update_request: I/O error, dev sdc, sector 57464 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 366.293505] ata5: EH complete
[ 366.973218] ata5.00: exception Emask 0x10 SAct 0x2000 SErr 0x4050002 action 0xe frozen
[ 366.973221] ata5.00: irq_stat 0x00400040, connection status changed
[ 366.973224] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 366.973227] ata5.00: failed command: READ FPDMA QUEUED
[ 366.973232] ata5.00: cmd 60/08:68:80:e0:00/00:00:00:00:00/40 tag 13 ncq dma 4096 in
res 40/00:98:78:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 366.973234] ata5.00: status: { DRDY }
[ 366.973237] ata5: hard resetting link
[ 367.753224] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 367.753449] ata5.00: configured for UDMA/33
[ 367.753461] ata5: EH complete
[ 368.443246] ata5.00: exception Emask 0x10 SAct 0x1000 SErr 0x4050002 action 0xe frozen
[ 368.443250] ata5.00: irq_stat 0x00400040, connection status changed
[ 368.443253] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 368.443256] ata5.00: failed command: READ FPDMA QUEUED
[ 368.443261] ata5.00: cmd 60/08:60:88:e0:00/00:00:00:00:00/40 tag 12 ncq dma 4096 in
res 40/00:a8:80:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 368.443263] ata5.00: status: { DRDY }
[ 368.443267] ata5: hard resetting link
[ 369.213226] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 369.213453] ata5.00: configured for UDMA/33
[ 369.213467] ata5: EH complete
[ 369.903220] ata5.00: exception Emask 0x10 SAct 0x80000000 SErr 0x4050002 action 0xe frozen
[ 369.903222] ata5.00: irq_stat 0x00400040, connection status changed
[ 369.903225] ata5: SError: { RecovComm PHYRdyChg CommWake DevExch }
[ 369.903228] ata5.00: failed command: READ FPDMA QUEUED
[ 369.903234] ata5.00: cmd 60/10:f8:00:e8:00/00:00:00:00:00/40 tag 31 ncq dma 8192 in
res 40/00:b8:88:e0:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 369.903235] ata5.00: status: { DRDY }
[ 369.903238] ata5: hard resetting link
[ 370.653223] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 370.653447] ata5.00: configured for UDMA/33
[ 370.653465] sd 4:0:0:0: [sdc] tag#31 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=1s
[ 370.653469] sd 4:0:0:0: [sdc] tag#31 Sense Key : Illegal Request [current]
[ 370.653487] sd 4:0:0:0: [sdc] tag#31 Add. Sense: Unaligned write command
[ 370.653491] sd 4:0:0:0: [sdc] tag#31 CDB: Read(10) 28 00 00 00 e8 00 00 00 10 00
[ 370.653495] blk_update_request: I/O error, dev sdc, sector 59392 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 370.653513] ata5: EH complete
[ 401.323228] ata5.00: exception Emask 0x0 SAct 0x2 SErr 0x0 action 0x6 frozen
[ 401.323233] ata5.00: failed command: READ FPDMA QUEUED
[ 401.323239] ata5.00: cmd 60/08:08:00:e8:00/00:00:00:00:00/40 tag 1 ncq dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 401.323241] ata5.00: status: { DRDY }
[ 401.323245] ata5: hard resetting link
[ 406.703213] ata5: link is slow to respond, please be patient (ready=0)
[ 411.393215] ata5: COMRESET failed (errno=-16)
[ 411.393222] ata5: hard resetting link
[ 416.753209] ata5: link is slow to respond, please be patient (ready=0)
[ 421.433210] ata5: COMRESET failed (errno=-16)
[ 421.433216] ata5: hard resetting link
[ 426.823208] ata5: link is slow to respond, please be patient (ready=0)
[ 456.463208] ata5: COMRESET failed (errno=-16)
[ 456.463217] ata5: hard resetting link
[ 461.513208] ata5: COMRESET failed (errno=-16)
[ 461.513216] ata5: reset failed, giving up
[ 461.513219] ata5.00: disabled
[ 461.513234] ata5: EH complete
[ 461.513258] sd 4:0:0:0: [sdc] tag#8 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=90s
[ 461.513263] sd 4:0:0:0: [sdc] tag#8 CDB: Read(10) 28 00 00 00 e8 00 00 00 08 00
[ 461.513267] blk_update_request: I/O error, dev sdc, sector 59392 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513271] Buffer I/O error on dev sdc, logical block 7424, async page read
[ 461.513327] sd 4:0:0:0: [sdc] tag#9 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513330] sd 4:0:0:0: [sdc] tag#9 CDB: Read(10) 28 00 00 00 e8 00 00 00 08 00
[ 461.513333] blk_update_request: I/O error, dev sdc, sector 59392 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513335] Buffer I/O error on dev sdc, logical block 7424, async page read
[ 461.513383] sd 4:0:0:0: [sdc] tag#10 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513386] sd 4:0:0:0: [sdc] tag#10 CDB: Read(10) 28 00 00 00 e8 00 00 00 08 00
[ 461.513389] blk_update_request: I/O error, dev sdc, sector 59392 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513390] Buffer I/O error on dev sdc, logical block 7424, async page read
[ 461.513430] sd 4:0:0:0: [sdc] tag#11 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513433] sd 4:0:0:0: [sdc] tag#11 CDB: Read(10) 28 00 00 00 e8 10 00 00 08 00
[ 461.513435] blk_update_request: I/O error, dev sdc, sector 59408 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 461.513461] sd 4:0:0:0: [sdc] tag#12 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513464] sd 4:0:0:0: [sdc] tag#12 CDB: Read(10) 28 00 00 00 e8 10 00 00 08 00
[ 461.513467] blk_update_request: I/O error, dev sdc, sector 59408 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513469] Buffer I/O error on dev sdc, logical block 7426, async page read
[ 461.513497] sd 4:0:0:0: [sdc] tag#13 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513500] sd 4:0:0:0: [sdc] tag#13 CDB: Read(10) 28 00 00 00 e8 38 00 00 08 00
[ 461.513503] blk_update_request: I/O error, dev sdc, sector 59448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 461.513525] sd 4:0:0:0: [sdc] tag#14 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513528] sd 4:0:0:0: [sdc] tag#14 CDB: Read(10) 28 00 00 00 e8 38 00 00 08 00
[ 461.513530] blk_update_request: I/O error, dev sdc, sector 59448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513532] Buffer I/O error on dev sdc, logical block 7431, async page read
[ 461.513560] sd 4:0:0:0: [sdc] tag#15 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513563] sd 4:0:0:0: [sdc] tag#15 CDB: Read(10) 28 00 00 00 e8 48 00 00 08 00
[ 461.513566] blk_update_request: I/O error, dev sdc, sector 59464 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 461.513589] sd 4:0:0:0: [sdc] tag#16 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513591] sd 4:0:0:0: [sdc] tag#16 CDB: Read(10) 28 00 00 00 e8 48 00 00 08 00
[ 461.513593] blk_update_request: I/O error, dev sdc, sector 59464 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 461.513594] Buffer I/O error on dev sdc, logical block 7433, async page read
[ 461.513616] sd 4:0:0:0: [sdc] tag#17 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[ 461.513618] sd 4:0:0:0: [sdc] tag#17 CDB: Read(10) 28 00 00 00 e8 78 00 00 08 00
[ 461.513620] blk_update_request: I/O error, dev sdc, sector 59512 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 461.513637] Buffer I/O error on dev sdc, logical block 7439, async page read
[ 461.513673] Buffer I/O error on dev sdc, logical block 7680, async page read
[ 461.513698] Buffer I/O error on dev sdc, logical block 7680, async page read
[ 461.513733] Buffer I/O error on dev sdc, logical block 7682, async page readВсё, хватит.
Наверное, таки умер…
Ну, святое дело — разобрать. Картинки кликабельны.
Вид спереди 
Что внутри 
Плата 
Плата
Да уж… не густо. И с паяльником не залезешь.
В заключение несколько советов/мыслей вслух:
Все пользователи компьютеров делятся на две группы: кто ещё не делает бекапы и кто уже делает бекапы. (есть разные версии этой поговорки).
- Регулярно делайте резервные копии важной информации. Приобретите внешний накопитель и периодически сохраняйте на нём информацию, которую будет жаль потерять. Каждый сам решит, что ему дорого.
- Используйте HDD, как дополнительный носитель. Не храните всё на SSD. Конёк SSD — скорость. Нет смысла хранить на нём архивы фильмов/музыки/фотографий. Используйте для хранения «больших и долгих данных» HDD.
- Максимально используйте SSD для системного раздела и файла подкачки (swap). Это значительно ускорит работу системы. Если носитель информации выйдет из строя — систему и программы всегда можно переустановить, это не занимает много времени. Я никогда не делаю резервную копию системного диска. Единственное, что сохраняю в резервной копии — каталог /etc. Всё остальное устанавливается и скачивается за несколько команд (я использую Linux. В случае использования другой операционной системы ситуация может быть иной)
- Подумайте об использовании RAID. В моём компьютере стоит дополнительно HDD-накопитель на 2ТБ. После этого случая я купил новый SSD на 120ГБ, из них отдал ~50ГБ под систему (/ — корневой раздел), остальное под раздел /home. На HDD создал раздел идентичного размера с SSD /home и объединил их оба в RAID-1 (зеркалирование) при помощи mdadm, а оставшееся место HDD примонтировал в /home/<username>/media. В итоге вся информация о конфигурации пользовательских программ хранится на RAID, а «большие долгие данные» в каталоге media.
- Возможно, есть смысл купить сразу два идентичных SSD и объединить их в RAID с зеркалированием. Скорость обращения упадёт незначительно, а сохранность данных повысится.
Спасибо, если дочитали до конца.
Не забывайте делать резервные копии.
Список форумов › Как у меня погиб SSD
Помечено: HDD, SSD
Вход / Регистрация
Вход / Регистрация